📖
Cerulean Sonar Docs
Docs DirectoryStore
Tracker 650
Tracker 650
  • Overview
    • CERULEANTRACKER DEPRECATION NOTICE
  • Quick Start for BlueROV / ArduSub Users
  • General Specifications
  • Configuring the Tracker 650
    • Finding the Configuration Web Page
    • Example Configuration Web Page
    • Live Status Page
    • Setting the Static IP Address
    • Setting the Fallback IP Address
    • Setting the Host IP Address
    • Setting the MAVLink REST Server Parameters
    • Setting Pool Mode
    • Setting DVL Mounting Rotation Offsets
      • Scenario: Driving Your Own Kalman Filter
        • Forward-Facing Mount
    • Setting Velocity Adjustment
  • General Usage
    • General Hints and Tips
    • Basic Operating Guidelines and Hints
    • Setting Speed of Sound
    • Scenario: Doing Your Own Dead Reckoning
    • Scenario: Holding Position
  • Using MAVLink and BlueOS for Position Hold on a BlueROV2
    • ArduPilot Parameters
    • Tracker 650 Setup for MAVLink Support
    • Global Origin
  • Mounting the Tracker 650
    • Bottom Mount
    • Thruster Deck Mount
      • Send xxx Message
  • Mounting Drawings (V1 pre-2025)
  • Communicating with the Tracker 650
    • Factory Defaults and Default Messages
    • The Ethernet Interface
    • Tips on How to Find the IP Address Assigned to Your Ethernet Adapter
    • Outgoing Message Formats, Tracker 650 to Host
      • $DVPDL and $DVPDX: DVL Position and Angle Deltas Messages
      • $DVNVM Non-Volatile Memory and Configuration
      • Freeform Error and Informational messages ($DVTXT)
      • $DVKFC Kalman Filter Raw Data Support Message
    • Commands Accepted by the Tracker 650
      • CONFIGURATION
      • SET-VELOCITY-ADJUSTMENT
        • SET-SPEED-OF-SOUND
      • SEND-DVPDL
      • SEND-DVPDX
      • SEND-DVKFC
      • SEND-MAVLINK-DISTANCE
      • MAVLINK-ORIGIN
      • SET-POSITION
      • SET-SENSOR-ORIENTATION
      • IP-ADDRESS
      • HOST-ADDRESS
      • MAVLINK-ADDRESS
      • FALLBACK-ADDRESS
      • UNICAST-TO-ME
      • PAUSE
      • RESUME
      • REBOOT
      • SET-POOL-MODE
    • Blue Robotics Discovery Protocol (Ethernet Only)
    • ARP (Address Resolution Protocol)
    • DHCP (Dynamic Host Configuration Protocol)
    • Ping (Internet Control Message Protocol Ping)
  • Coordinate Systems
  • Mounting Drawings (V2 post-2024)
  • CAD Models
  • Electrical Drawings
    • Power and Ethernet Cabling
  • Expectations
  • Copyright
Powered by GitBook
On this page
  1. Configuring the Tracker 650
  2. Setting DVL Mounting Rotation Offsets
  3. Scenario: Driving Your Own Kalman Filter

Forward-Facing Mount

PreviousScenario: Driving Your Own Kalman FilterNextSetting Velocity Adjustment

Last updated 3 months ago

Looking at the front of a BlueROV2 Heavy with the Tracker 650 mounted on the bow facing forward. Note the arrow pointing to the starboard side of the ROV; if the the arrow was pointed up the cable would project below the bottom of the ROV, and if the arrow was pointed down the cable would interfere with the electronics enclosure. Since this is not the default orientation you will need to send a command (only once since it will be stored in non-volatile memory) with parameters (90, 0, 90).
Iso view of the mounting in the previous figure: the front of a BlueROV2 Heavy with the Tracker 650 facing forward. Note the arrow pointing to the starboard side of the ROV. The battery tube can be shifted aft to provide clearance and improve balance.
SET-SENSOR-ORIENTATION